FH GroupFront Set Faux Leather Car Seat Covers for Low Back Seat with Removable Headrest, Universal Fit, Airbag Compatible Seat Cover for SUV, Van, Black

I purchased these seat covers for a 2010 Toyota Tacoma. I have the double cab with 60-40 split folding rear seats, no side air bags. The front seats took about an hour to install total. I struggled a little trying to route the straps under the seat. But, when completed, I was very pleased with how well the seat covers looked, fit and feel. They do look very close to "leather" seats but feel a little softer. The covers do not appear to move around when getting in and out of the seats.I was not quite as pleased with the rear seat covers. Since they are a "universal fit", they have a series of zippers to account for split folding seats. When you want to spit the seats, you unzip the closest zipper. The bottom seat cover fit went on fairly well, but I wish it had a few more straps. The back seat cover was a struggle, since you basically need to pull it across the whole seat at once. Since it is a split seat, it wants to fall down on you while you are pulling on the seat cover. It could have used a few more straps. But, I got it on and it fits reasonably well. The back and bottom rear seat covers did not wrinkle and do not appear to shift around when getting out of the seat. They look pretty close to leather also. Someone looking into your car may think you have leather seats.Again since this is a universal fit, you need to make modifications for the seat belts and pull straps. I was able route the bottom seat belt latches through the zippers (unzip the cover at back of bottom bench seat). I had to cut a slit in the top of the back seat cover (which is what the instructions tell you to do) for the split pull release. It does not appear to be tearing and looks fine. I have not been able to figure out how to route the center seat belt strap yet. The instructions say to cut from the edge and route the seat belt, but it's close to a zipper and I think it will look bad. I would rather unbolt the seat belt from the frame, cut a slit and run it through that way. Still thinking about it.....Overall for $69.99 this is a great buy. Just wanted everyone to be aware that it takes some work to get them installed.

These are semi-custom car seat covers - realize that they are not exact fit and may have some areas that don't fit like a glove. These are designed to fit a wide range of seats. Also, the pictures were taken right after install. Only time will tell if the wrinkles/puckers will smooth out with use.Upon opening these seat covers (they came in a very nice package), there is an odor from the material that needs to off-gas (air out). This is a normal for synthetic materials that didn't get the chance to fully off-gas before packaging. I simply unfolded all the seat covers and spread them out in my garage overnight. The odor was gone by the next morning. I would highly suggest doing this. The instructions direct you to install videos which help too. I have installed car seat covers years ago so I was familiar with the process. That prior knowledge made install easy for me, especially since this was in a minivan where I had access to the front,back, and underside of the seats (the seats pivot and can also be removed easily).Key to remember - the non-leatherette material (on sides and backs) is very thin and you need to be careful not to pull too hard on any strap during install as it can rip the seams. This isn't a cargo strap - it just needs to hold the cover in place and minimize wrinkles/movement. The seat covers do not have holes for arm rests so you will have to remove armrests and cut holes in the side material so they will fit. Not hard, but you want to make sure you get it right before cutting. Same for the rear head rests - you have to cut holes for them too. The middle seat covers had Velcro closure for the headrests so no holes there.One more install note - in my last picture (where you can see the cover on the split bench seat folded down), there is an optional set of thin mesh zippered pieces (they come as 2 pcs zipped together as 1) which can be used in the split bench. I chose to use them as side pieces for the top seat-backs as it allows you to recline the bench seats individually without having to unzip the seat cover. In this configuration, if you want to stow the bench seat, you will have to unzip the seat-bottom along the seam/zipper to separate the split bench. You could instead use the mesh inserts along the seat-back and seat-bottom to avoid any unzipping during stowage, but one side of the split bench will not be covered. Since I don't stow the seats often, I would rather have a cleaner look along the seat-back split.I ranked this 4 stars, but only barely as I really like these covers - the reason it lost a star was that one of the seams in the leatherette material (seam in the seat) was completely unraveled and open. I noticed the hole in the seam (about 2-3 inches long) during install and immediately removed the seat cover. Instead of returning the covers for a replacement, I just sewed the seam back together following the stitching and fixed it myself. I blame the quality control as that was a pretty big seam to miss. Regardless, I would not install the cover with that defect as it would have quickly unraveled more during use and rendered that seat cover useless. Key takeaway = inspect your seams BEFORE install to make sure the covers are good to go.Beside that one bad seam, the covers look very nice and feel great! They have only been on a week but so far hold up well to kid-wear-and-tear. I'll update this if they fail or otherwise not meet my expectations. My least favorite fit in the minivan was the center row head rests - the headrest covers are wider than the headrests and don't look great. I almost didn't install them, but after everything was in the van, you can adjust them some to make them look better. Again, these are semi-custom.Overall, I like the seat covers and hope the installed pictures help my 2012 Kia Sedona friends get an idea of what they will look like in their minivan.If you feel my review was helpful, please click "helpful" below. Thank you!

Me gusta el producto pero lo tuve que devolver varias veces, no llegaba completo, sólo subo fotos de los asientos delanteros porque el asiento trasero es muy complicado de instalar, no hay instrucciones. Muy poco satisfactorio, creo que esta compañía no toma en cuenta los comentarios de los clientes.

I love the quality, texture and how easy it was to install. I Would strongly recommend purchasing this product.

They fit nice and the colour matched the interior of the truck. Easy to install. I didn’t have them long enough to know if the quantity of them but they look nice and a good price.

ممتاز

Looks better than expected. Fits well other than headrest a bit to big.